T3 GT3582 GT35 A/R 0.63 0.7 Anti Surge housing Turbo charger Turbocompresor
T3 GT3582 GT35 A/R 0. 63 0.7 Anti Surge housing Turbo charger Turbocompresor. Perfect for all 4/6 cylinder and 2.5L-6.0L engines Horse Power: Capable of Boosting Horse Power up to 600HP.Notice: Please confirm that there is enough space in your car to install this turbo before purchasing. Turbine Side: Exhaust Inlet Flange: T3 Flange Exhaust Outlet Flange: 4-Bolt Turbine Trim: 84.2 Turbine A/R: 0.63 Turbine Inducer Diameter: 68mm Turbine Exducer Diameter: 62.4mm Compressor Side: Compressor Trim: 56.9 Compressor A/R: 0.7 Compressor Inducer Diameter: 61.5mm Compressor Exducer Diameter: 81.5mm Compress Inlet Size(Air intake): 4 inch (103.5mm) Compressor Outlet Size: 2.5 inch (63.6mm).
Bearing Type: Floating/Journal Bearing Thrust bearing: 270 degree Cooling Type: Water + Oil Cooling Horse Power: Up to 600HP Turbo Type: Individual Wastegate: W/O Wastegate Oil feed/inlet: M107/16-24 Oil drian/outlet: M14.1 & 2M81.25 Water inlet/outlet: M14 1.5 Maximum PSI: 22 Condition: 100% Brand New Accessories: You will get exactly as shown as picture above Pakage Size: 26 x 25 x 23 cm Pakage Weight: 8350g. 1 xTurbocharger 2 x Flange gaskets 2 x Oil feed/drain gaskets. Turbine housing : Ductile iron QT450-10 shell with high-temperature resistance up to 700 degrees Celsius 2. Steel Turbine Wheel: Made from the special K418 alloy to achieve high oxidation resistance and stability under high temperatures up to 900 degrees Celsius 3.Compressor housing: ZL104 aluminum 4. Compressor wheel/blades: Cast aluminium with good gas tightness and corrosion resistance 5. Max HP: UP to 600hp. Turbine housing : Ductile iron QT450-10 - temperature resistant up to 700?
Steel turbine wheel: K418 alloy - high oxidation stability and resistance up to 900? Compressor housing: ZL104 aluminum with lightweight 4.Compressor wheel/blades: Cast aluminium blades - superior air tightness & corrosion resistance. Cost-effective turbo increase 20-40% power for your car 2. Rich experience in turbo production and own factory 3. High-Speed oil seal ring and Precision clearance 4. Built for durability and strength. 100% balancing Test by TURBOTECHNICS VSR3 2. G3-min-Flow VNT Turbo testing 3. We highly recommend you make sure the points below before installing: 1. Replace the air filter: if the if the air filter is not replaced may cause the compressor wheel damage. Replace the engine oil: Because floating bearing and turbocharger will be damaged by impurities in the old oil. After large overhaul, the engine cannot be replaced with a new turbocharger because there are too much impurities in oil after overhauling which will damage the replacement turbocharger immediately. Please run the old turbocharger for 7-10 days and then replace to new turbocharger and new engine oil. Make sure the oil drain line is lower than the turbo itself. Gasoline car must install a water cooling device to avoid overheating. Ensure exhaust outlet are well sealed by welding The degree of modification of the universal turbo depends on your individual vehicle. Professional installation is highly recommended. This Turbo is not vehicle specific. Please check the specifications and verify compatibility prior to placing your order.
Before installing the new turbocharger, the cause that led to the failure of the turbo must be analyzed and eliminated e. Insufficient oil supply, foreign bodies in the intake area, crankcase ventilation without function, etc. Will this fit my car?
Please make sure you have read through the whole listing and paid attention to "note" and "notice". When will my order be dispatched? What do I do if I have not received my order? Can I amend my order?
- Application: Perfect for all 4/6 cylinder and 2.5L-6.0L engines
- bearing type: journal bearing, wet bearing
- Brand: maXpeedingrods
- Compressor Air Inlet: 4 inch (103.5mm)
- Compressor Air Outlet: 2.5 inch (63.6mm)
- Compressor housing A/R: 0.7 A/R
- Cooling Type: Water & Oil cooled
- Dimensions (Length Width Height): 230*180*240 mm
- Exhaust Inlet (Turbo Manifold) Flange: T3 Flange
- Exhaust Outlet Flange: 4 bolt
- Features: Individual
- Finish: Matte
- Horse Power: Capable of Boosting Horse Power up to 600HP
- Interchange Part Number: for all 4/6 cyl ,2.5L-6.0L engines
- Manufacturer Part Number: N6U57Q
- Manufacturer Warranty: 2 Years
- Maximum PSI: 22
- Oil drian/outlet: M14.1 & 2*M8*1.25
- Oil feed/inlet: M10*7/16-24
- Reference OE/OEM Number: GT35 gt3582, GT3582 anti-surge anti surge Turbine, turbo charger turbolader, turbocompressor turbocharger, High performance aftremarket parts, GT35 GT3582 Turbo Turbocharger
- Superseded Part Number: GT3582
- Thrust bearing:: 270 degree
- Turbine Housing A/R: 0.63 A/R
- Type: Turbocharger
- Universal Fitment: Yes
- Water Hole Size: M14* 1.5
- EAN: 6941324413838